Parts

Parts Products included  Count. Note
5M4.070.042
(The sensor AN-7529/60, AN-7529/60M)
5M2.840.066 electrode system  1  
5M6.215.003 liner 1 Only for AN-7529 and AN-7529M - plastic liner with two rubber pads and the "window" of the cellulose film. Located between the two parts of the vessel.
5M6.215.004 liner  1 Only for AN-7560 and AN-7560M (the rest see above).
5M6.393.011 Pinwheel 1 Is attached to the axis of the motor encoder. Used for mixing the solution with in-court.
5M6.434.005 Frame  1 The frame of a metal grid within which vane rotates. Gaeta located in the vessel.
5M7.840.071 Gasket  100 Of cellulose film 58h58 mm liner and 5M6.215.003 5M6.215.004 (see above).
5M8.241.011-04 Ring  5 Rubber ring ext. Ø23, 5, ext. Ø29, 5. Located on the bottom of the sleeve in the electrode system 5M2.840.066 to seal when installing the system on the plate electrode sensor.
5М4.070.043 
(газовому тракту к 
и АН-7529/60 
АН-7529/60М)
 
5M5.150.000 Throttle 1 Three glass tubes with ext. Ø0, 5, ext. Ø4 ... 6, connected to each other by two rubber tubes. Installed on the output of the filter-absorber provides the necessary flow of oxygen.
5M5.886.002 Filter  1 Filter with a cotton swab inside. To clean the oxygen-gas mixture of dust formed after combustion of the sample in the oven.
Fitting 5M6.454.002  1 Nozzle assembly with a rubber stopper, nut and the tap-off nozzle. Closes the rear end of the porcelain tube installed in the furnace.
5M7.010.004 Throttle 4 Glass tube with internal. Ø0, 5, ext. Ø4 ... 6, l = 80 ± 1,5. Included in choke 5M5.150.000 (see above).
5M8.241.011-03 Ring 5 Ext. Ø19, 5, ext. Ø26, 7. Rubber O-rings for the shutter, which seals the porcelain pipe that is installed in the furnace.
5M8.241.011-05 Ring 5 Ext. Ø24, 5, ext. Ø31, 7
5M8.241.011-06 Ring 5 Ext. Ø29, 5, ext. Ø38, 7. Rubber ring is installed in 5M5.886.002 filter (see above) between cover and filter for leaks.
5M4.070.044 
(the sensor AS-7932 and AS-7932M)
5M2.840.075 electrode system   1  
5M6.614.003 plate   The plate is a ring made of polystyrene with external Ø22, inside of which a ceramic wall. Placed at the bottom of the cathode chamber (housing 5M6.116.088) and at the bottom of the anode compartment (short-empty 5M6.116.089). (See zap.komplekt 5M4.070.062).
5M7.010.005 Throttle  2 Glass tube with internal. Ø0, 8, ext. Ø6, 5 ... 8, l = 35. Set in a fine filter on the sensor plate. Allowed throttle-tion with reduced internal diameter and the length of the throttle decreases proportionally to the decrease in the cross-section holes. 
5M7.867.011 Tube  2 Polypropylene tube, vnesh.Ø3, l = 127. Installed in connection 5M6.454.004 serving for supplying the sample gas in the cathode compartment. (See zap.komplekt 5M4.070.060-01). 
5M8.241.011-02 Ring Rubber ring, ext. Ø5, 7, ext. Ø9, 5. Set in a fine filter to fix the throttle 5M7.010.005 (see above). Xia also uses the O-ring in the socket for the supply of the sample gas in the cathode compartment. 
5M8.241.011-04 Ring  5 Rubber ring, ext. Ø23, 5, ext. Ø29, 5. Located on the bottom of the sleeve in the electrode system 5M2.840.075 to seal when installing the system on the plate electrode sensor. Is also set to seal the filter, located upstream gas treatment unit (slot "oxygen").
5M8.683.248 Ring 4 Rubber ring ext. Ø16, 5, ext. Ø22. To seal in the joints 5M6.614.003 plate (see above) with the cathode and anode compartments in the hull.
5M4.070.045 
(to the gas path 
AS-7932 and AS-7932M)
 
5M7.010.006 Throttle 2 Glass tube, ext. Ø0, 5, ext. Ø4 ... 6, l = 35. Is set to point at the panel of the gas treatment (female "Sensor"), through which passes the flow blowing.
5M8.241.011-03 Ring 5 Rubber ring, ext. Ø19, 5 for the gate, which seals the porcelain pipe that is installed in the furnace. 
Also installed to seal in the gearbox mounted in the gas treatment unit (between the body and the bottom flange of the gearbox.) 
is also set in the filter-cooler (gazootbornike) for sealing-tion between the filter Coarse and clamping device.
5M8.241.011-05 Ring 5 Rubber ring vnutr.Ø24, 5, ext. Ø31, 7, to seal the gate.
5M8.241.011-08 Ring 5 Rubber ring vnutr.Ø3, 8, ext. Ø7, 6, to seal the throttle 5M7.010.006 (see above) when it is installed in the socket.
 5M4.070.052 
(to the sensor and AN-7529/60 AN-7529/60M)
  
5M2.329.001 sensor or 
sensor 5M2.329.001-01
-04 sensor 5M2.329.001 
5M2.329.001-05 Sensor

1
1
1
к АН-7529 
-7560 к АН 
к АН-7529М 
к АН-7560M
5M6.393.011 Pinwheel  1 Axis is fixed to the engine sensor. Used for mixing the solution in the vessel. 
5M6.434.005 Frame  1 The frame of a metal grid within which vane rotates. Located in the vessel. 
5M6.215.003 liner 1 Only for AN-7529 and AN-7529M. Plastic liner with two rubber pads and Vym "window" of the cellulose film. Located between the two parts of the vessel.
5M7.840.071 Gasket  100 Of cellulose film 58h58 mm liner and 5M6.215.003 5M6.215.004 (see above)
5M8.241.011-04 Ring  5 Rubber ring from vnutr.Ø23, 5, ext. Ø29, 5. Located on the bottom of the sleeve in the electrode system for sealing the installation of the plate electrode sensor.
5М4.070.053 
5М4.070.053-01 
5М4.070.053-02
5M2.229.009 unit measuring 
5M2.229.009-01 block measuring 
5M2.229.009-02 measuring unit
1
1
к АС-7932М 
АН-7529М к 
к АН-7560М
5M4.070.054 
(to the gas path 
AS-7932 and AS-7932M)
 
5M5.886.004 filter-cooler In the filter-cooler (gazootbornik) includes: clamping device that is installed on the stove, the coarse filter with the set screw, the gas outlet. 
5M4.070.055 
(to the gas path 
AS-7932 and AS-7932M)
 
5M6.457.000 Flue   Stainless steel tube, l = 266, with two channels and two unions. Included in the filter-cooler (gazootbornik). (See zap.komplekt 5M4.070.054).
5M4.070.056 
(to the combustion device)
 
7077.01.02.015 cap  600 Aluminum caps height of 8 mm, ext. Ø15, 5 mm. Are placed on the ends of the heater before you install them in the oven to improve electrical contact.
5M4.070.057 
(the sensor AN-7529 and AN-7529M)
 
5M7.840.070 Cover  50 Rubber pads. Beginning to insert 5M6.215.003 (see zap.komplekt 5M4.070.042) - only for AN-7529, AN-7529M.
5M4.070.057-01 
(the sensor AN-7560 and AN-7560M)
 
5M7.840.072 Cover  50 Rubber pads. Beginning to insert 5M6.215.004 - only for AN-7560 and AN-7560M.
5М4.070.058 
(к газовому тракту 
АН-7529/60, 
АН-7529/60М, 
АС-7932 и АС-7932М)
5M6.272.004 Shutter 1 Designed to seal the porcelain tube, setting it in the oven. Consists of a body with a bracket attached to it and the connection of the two hinged covers - locking and sealing, cap nut and washer.
5M4.070.059 
(to the gas treatment unit)
5M2.954.002 gas treatment unit 
or
1 For AN-7529 and AN-7529M
5M2.954.002-01 gas treatment unit 1 For AN-7560 and AN-7560M.
5M2.954.003 gas treatment unit 1 For AS-7932 and AS-7932M.
5M5.150.000 Throttle 1 Only AN-7529/60 and AN-7529/60M (see zap.komplekt 5M4.070.043).
5M7.010.004 Throttle 4 Only AN-7529/60 and AN-7529/60M (see zap.komplekt 5M4.070.043).
5M7.010.006 Throttle 2 For AS-7932 and AS-7932M (see zap.komplekt 5M4.070.045).
5M8.241.011-03 Ring 5 For all ANOVA and aces (see zap.komplekt 5M4.070.045).
5M8.241.011-05 Ring 5
5M8.241.011-06 Ring 5 Only AN-7529/60, AN-7529/60M (see zap.komplekt 5M4.070.043).
5M8.241.011-08 Ring 5 For AS-7932 and AS-7932M (see zap.komplekt 5M4.070.045).
5М4.070.060 
(газовому тракту к 
и АН-7529/60 
АН-7529/60М)
 
Fitting 5M6.454.002  1 Only AN-7529/60 and AN-7529/60M. Acts as a stopper sealing the rear end of the porcelain tube installed in the furnace. Consists of a brass ribbed body, branch fittings, rubber stopper and a massive metal nut.Length fitting (tube) of 100 mm.
5М4.070.060-01 
(датчику к 
и АС АС-7932-7932М)
 
Fitting 5M6.454.004 1 For AS-7932 and AS-7932M. Nozzle assembly with a polypropylene tube Ø 3 mm, length of the tube 127.Fitting with a tube length 182 mm. Fitting is installed on the sensor plate to supply the sample gas in the cathode compartment.
5M4.070.061 
(the sensor AN-7560 and AN-7560M)
 
5M8.610.037 plate  100 Zinc plate 125h16 mm, thickness 2 mm (thickness allowed 3.5 ... 4 mm), serves as a zinc electrode. Is used as the anode and screw in the left compartment of the vessel electrolytic cell.
5M4.070.062 
(the sensor AS-7932 and AS-7932M)
 
5M6.614.003 plate  20 The plate is a ring made of polystyrene, vnesh.Ø22, height 8, inside of which a ceramic wall. Placed at the bottom of the cathode chamber (housing 5M6.116.088) and at the bottom of the anode compartment (housing 5M6.116.089).
5М4.070.063 
(к датчику АС-7932 и 
АС-7932М)
 
5M2.329.002 sensor 1  
5M6.116.089 Case  1 Housing Assembly (anode compartment). Is a glass cylinder, the bottom of which is set with a ceramic plate 5M6.614.003 partition (see zap.komplekt 5M4.070.044). At the junction of the body to the plate using a rubber ring 5M8.683.248 (see zap.komplekt 5M4.070.044). Housing is mounted on a plate sensor.
Fitting 5M6.454.004 1 See zap.komplekt 5M4.070.060-01.
5M6.614.003 plate  1 Sm.zap.komplekt 5M4.070.044. The plate includes a housing and 5M6.116.088 5M6.116.089.
5M7.010.005 Throttle 2 See zap.komplekt 5M4.070.044
5M7.867.011 Tube 2
5M8.241.011-02 Ring 5
5M8.241.011-04 Ring  5
5M8.683.248 Ring 4
PVC tube 4x6 0.4 m Worn on the nipple 5M6.454.001 (see above) for the supply of the sample gas in the cathode compartment.
5М4.070.064 
(газовому тракту к 
и АН-7529/60 
АН-7529/60М)
 
5M5.886.002 Filter  1 Filter with a cotton swab inside. To clean the oxygen-gas mixture of dust formed after combustion of the sample in the oven.
5M4.070.065 
(to the sensor and AN-7529/60 AN-7529/60M)
 
5M7.840.071 Gasket  5000 Of cellulose film 58h58 mm. to insert and 5M6.215.003 5M6.215.004 (see zap.komplekt 5M4.070.052).
5М4.070.066 
(к измерит. блоку 
АН-7529/60, 
АН-7529/60М, 
АС-7932, АС-7932М)
5M6.645.052 cable connection 1 Cable assembly with two forks to 16 contacts. To connect corrector weight.
5М4.070.068 
(к датчику АН-7529 и АН-7529М)                  -01                  -02

 
5M8.610.033 plate  100 Zinc alloy plate U0, 125h50 mm, 4 mm thick. Plays the role of the zinc electrode. Is used as the anode and screw in the left compartment of the vessel electrolytic cell.
5M8.610.033 plate  200 Zinc plate belt C1-2, 125h50 mm, thickness 2 mm.
5M8.610.033 plate  10 Zinc alloy plate U0, 125h50 mm, 4 mm thick. 
above said plate is made ​​of a zinc strip thickness of 2 mm, allowed to produce cast alloy thickness of 3.5 ... 4 mm, ie are variants of the same plate.
 
5М4.070.069 
(к датчику АН-7529/60 и АН-7529/60М) 
                 -01 
                 -02 
                 -03 
                 -04 
                 -05
5M5.570.000 vessel 1 For AN-7529 and AN-7529M
5M5.570.001 vessel 1 For AN-7560 and AN-7560M.
5M5.570.000 vessel 2 For AN-7529 and AN-7529M
5M5.570.001 vessel 2 For AN-7560 and AN-7560M.
5M5.570.000 vessel 5 For AN-7529 and AN-7529M
5M5.570.001 vessel 5 For AN-7560 and AN-7560M.
5М4.070.070 
(датчику к 
и АС АС-7932-7932М)
 
5M6.116.088 Case 1 Housing (cathode compartment) assembly with a cathode 5M5.500.003. The cathode contains a platinum wire Ø1, 5.
5M6.614.003 plate  1 (See zap.komplekt 5M4.070.044). Located in the lower part of the body (cathode-tion is marked.)
5M8.683.248 Ring 2 (See zap.komplekt 5M4.070.044). Established in connection with the case of the plate 5M6.614.003 5M6.116.088 (see above).
1E8.685.659 Gasket  2 Rubber ring ext. Ø10, ext. Ø15 to seal the installation of the cathode in the case.
5M4.070.070-01 5M6.116.088-01 Case  1 Housing Assembly (cathode compartment), but without the cathode plates, rings and gaskets (see above).
5М4.070.071 
(датчику к 
и АС АС-7932-7932М)
 
5M5.500.004 Anode 1 A cylindrical casing made of polypropylene, closed with two sides brass and rubber bushings. From the case of the rubber sleeve serves touch of platinum wire Ø1, 5. Length by contact - 20 mm. Fits into the anode (anode compartment), the arrangement of the sensor on the stove.
  5M6.116.089 Case  1 Housing Assembly (anode compartment). Is a glass cylinder, the bottom of which is set 5M6.614.003 plate. In place of the compound housing the plate using a rubber ring 5M8.683.248. Housing is mounted on a plate sensor.
  5M6.614.003 plate  1 (See zap.komplekt 5M4.070.044). Located in the lower part of the body 5M6.116.089 (anode compartment). (See above.)
  5M8.683.248 Ring 2 (See zap.komplekt 5M4.070.044). Installed at the junction of the plate to the housing HN 5M6.614.003 5M6.116.089 (see above).
5М4.070.071-01 
(датчику к 
и АС АС-7932-7932М)
 
5M6.116.089 Case  1 Body complete with plate and ring (see above).